Kia Soul: Steering Gear box. Replacement - Electric Power Steering - Steering SystemKia Soul: Steering Gear box. Replacement

Kia Soul 2014-2019 PS Service Manual / Steering System / Electric Power Steering / Steering Gear box. Replacement

1.
Loosen the wheel nuts slightly.
Raise the vehicle, and make sure it is securely supported.
2.
Loosen the bolt and then disconnect the universal joint assembly (A) from the pinion of the steering gear box.
Tightening torque :
32.4 ~ 37.3N.m (3.3 ~ 3.8kgf.m, 23.9 ~ 27.5lb-ft)

  
• Do not use the bolt again.
3.
Remove the front wheel and tire (A) from front hub.
Tightening torque :
88.2 ~ 107.8N.m (9.0 ~ 11.0kgf.m, 65.0 ~ 79.5lb-ft)

  
Be careful not to damage to the hub bolts when removing the front wheel and tire (A).
4.
Remove the stabilizer link (A) loosening the nut.
Tightening torque :
98.1 ~ 117.7N.m(10.0 ~ 12.0kgf.m, 72.3~86.8lb-ft)

5.
Remove the tie rod end ball joint (C) from the knuckle by using the SST (09568-34000).
(1)
Remove the split pin (A).
(2)
Remove the castle nut (B).
(3)
Use the SST (09568-34000).
Tightening torque :
23.5 ~ 33.3N.m(2.4 ~ 3.4kgf.m, 17.4 ~ 24.6lb-ft)

  
•
When using SST, be sure not to damage the dust cover of lower arm ball joint.
•
Keep SST tied to the car because there is a risk of injury by dropping the SST during removing the lower arm ball joint.
•
The peripheral parts may be damaged when removing the lower arm ball joint with a general tool such as lever, so be sure to use SST.
6.
Loosen the bolt & nut and then remove the lower arm (A).
Tightening torque :
58.9 ~ 70.6 N.m (6.0 ~ 7.2 kgf.m, 43.4 ~ 52.1 lb-ft)

7.
Loosen the bolt and then separate the roll rod stopper (A).
Tightening torque :
107.9 ~127.5N.m(11.0 ~ 13.0kgf.m, 79.6 ~ 94.0lb-ft)

8.
Disconnect the muffler rubber hanger (A).
9.
Loosen the bolts & nuts and then remove the sub frame (A).
Tightening torque :
Sub frame mounting bolt & nut
156.9 ~ 176.5N.m(16.0 ~ 18.0kgf.m, 115.7 ~ 130.2lb-ft)

10.
Remove the heat protector (A).
Tightening torque :
6.9 ~ 10.8N.m(0.7 ~ 1.1kgf.m, 5.1 ~ 7.9lb-ft)

11.
Remove the stabilizer (A) from the front sub frame by loosening the mounting bolts & nuts.
Tightening torque :
44.1 ~ 53.9N.m(4.5 ~ 5.5kgf.m, 32.5 ~ 39.8lb-ft)

12.
Remove the gear box (A) from the front sub frame by loosening the mounting bolts.
Tightening torque :
88.3 ~ 107.9N.m (9.0 ~ 11.0kgf.m, 43.4 ~ 57.9lb-ft)

13.
Installation is the reverse of removal.
  
•
Must be ASP calibration and EPS type recognition after assembling.
14.
Check the wheel Alignment.
(Refer to Suspension System - "Alignment")
    Steering Gear box. Components
    1. Steering Gear box ...

    Steering wheel
    ...

    See also:

    Random
    While song (file) is playing (RDM) key My Music mode: RDM on screen Random (press the key) : Plays all songs in random order. USB mode: FLD.RDM on screen Folder Random (press the key) ...

    Rear Bumper Cover Component Location
    1. Rear bumper cover ...

    Rear Seat Folding Lever Replacement
       • Put on gloves to protect your hands. ...