Kia Soul: Rear Seat Back Cover Replacement
[LH] |
|
|
1. |
Remove the rear seat back assembly [LH].
(Refer to Rear Seat - "Rear Seat Assembly")
|
2. |
Push the lock pin (B), remove the rear seat headrest (A).
|
3. |
Remove the lock hook (B) and then remove the rear seat armrest
(A).
|
4. |
Press the rear seat armrest (A) in the direction of the arrow
in the below picture, and then remove it by pulling it up.
|
5. |
Using a screwdriver or remover, remove the rear seat folding bezel
(A).
|
6. |
Using a screwdriver or remover, remove the rear seat belt center
cover (A).
|
7. |
Using a screwdriver or remover, remove the tether anchor ganish
(A).
|
8. |
Using a screwdriver or remover, remove the rear seat back bush
hinge (A).
|
9. |
Remove the protector (A) located in the bottom side of the rear
seat back.
|
10. |
Zip off the rear seat back cover located in the side (A), and
then pull it up.
|
11. |
Pull out the hooks (A) by the rear seat back frame.
|
12. |
Turn the rear seat back cover inside out. Then pull out the headrest
guides (A) while pinching both sides of the lower part of the guides,
and remove them.
|
13. |
Remove the rear seat back cover (A) from the rear seat back frame
(B).
|
14. |
After removing the hog-ring clips (A) on the rear of seat back
and remove the rear seat back cover (B).
|
15. |
Install in the reverse order of removal.
|
[RH] |
|
|
1. |
Remove the rear seat back assembly [RH].
(Refer to Rear Seat - "Rear Seat Assembly")
|
2. |
Push the lock pin (B), remove the rear seat headrest (A).
|
3. |
Using a screwdriver or remover, remove the rear seat folding bezel
(A).
|
4. |
Using a screwdriver or remover, remove the tether anchor ganish
(A).
|
5. |
Using a screwdriver or remover, remove the rear seat back bush
hinge (A).
|
6. |
Remove the protector (A) located in the bottom side of the rear
seat back.
|
7. |
Zip off the rear seat back cover located in the side (A), and
then pull it up.
|
8. |
Pull out the hook (A) by the rear seat back frame.
|
9. |
Turn the rear seat back cover inside out. Then pull out the headrest
guides (A) while pinching both sides of the lower part of the guides,
and remove them.
|
10. |
Remove the rear seat back cover (A) from the rear seat back frame
(B).
|
11. |
After removing the hog-ring clips (A) on the rear of seat back
and remove the rear seat back cover (B).
|
12. |
Install in the reverse order of removal.
|
Rear Seat Back Cover Component Location
1. Rear seat back cover [LH] 2. Rear seat back cover [RH] ...Rear Seat Cushion Cover Component Location
1. Rear seat cushion cover ...See also:
ETC (Electronic Throttle Control) System. Specifications
Specification
[TPS1]
Item
Opening Percentage
(%)
Output Voltage (V)
[Vref = 5V]
C.T
7 ~ 13
0.35 ~ 0.65
W.O.T
88.6 ~ 94
...
Rear Oil Seal Removal
1.
Remove the transaxle assembly.
(Refer to Manual Transaxle System - "Manual Transaxle")
(Refer to Automatic Transaxle System - "Automatic Transa ...
Passenger Airbag (PAB) Module. Installation
1.
Remove the ignition key from the vehicle.
2.
Disconnect the battery negative cable from battery and wait for
at least thirty seconds bef ...