Kia Soul: Piston and Connecting Rod Reassembly - Cylinder Block - Engine Mechanical SystemKia Soul: Piston and Connecting Rod Reassembly

Kia Soul 2014-2019 PS Service Manual / Engine Mechanical System / Cylinder Block / Piston and Connecting Rod Reassembly

  
•
Thoroughly clean all parts to assembled.
•
Before installing the parts, apply fresh engine oil to all sliding and rotating surfaces.
•
Replace all gaskets, O-rings and oil seals with new parts.
1.
Assemble the piston and the connecting rod.
(1)
Use a hydraulic press for installation.
(2)
The piston front mark (A) and the connecting rod front mark (A) must face the timing chain side of the engine.

Pressing load : 500 ~ 1,500 kg (1,102 ~ 3,306 lb)

2.
Assemble the piston rings.
(1)
Install the oil ring coil spring and two side rails by hand.
(2)
Using a piston ring expander, install the 2 compression rings with the code mark facing upward.
(3)
Position the piston rings so that the ring ends are as shown.

3.
Assemble the connecting rod bearings.
(1)
Align the bearing (A) claw with the groove of the connecting rod and cap (B).
(2)
Install the bearings (A) in the connecting rod and cap (B).

4.
Insert the piston and connecting rod assemblies into the cylinder bores.
  
Before installing the piston, apply a sufficient amount of engine oil to the ring grooves and cylinder bores.
(1)
Press the piston rings with a ring compressor and check that the rings are securely in place. Then insert the piston into the cylinder bore, and tap it in using the wooden handle of a hammer.

(2)
Stop after the ring compressor pops free, and check the connecting rod-to-crank journal alignment before pushing the piston into place.
(3)
Install the rod caps with bearings, and tighten the bolts.

Tightening torque :
17.7 ~ 21.8 N.m (1.8 ~ 2.2 kgf.m, 13.0 ~ 15.9 lb-ft) + 88 ~ 92°

  
Always use new connecting rod cap bolts. Connecting rod cap bolts are toque-to-yield bolts designed to be permanently elongated beyond the state of elasticity when torqued, so if the bolts are removed and reused, it may cause the bolts to break or fail to maintain clamping force.
5.
Check the side clearance between piston and connecting rod.
6.
Install the ladder frame.
(1)
Apply the liquid gasket on the ladder frame.

Bead width : 2.5 ~ 3.5 mm (0.0984 ~ 0.1378 in)

  
•
Apply the sealant, THREE-BOND 1217H or LOCTITE 5900H on the ladder frame rail portion and install it within five minutes. If sealant is applied to cylinder block bottom position, the sealant position should be the same as that of the ladder frame rail.
•
Apply sealant along the inner line of the bolt holes.
(2)
Install the ladder frame (A).

Tightening torque :
18.6 ~ 23.5 N.m (1.9 ~ 2.4 kgf.m, 13.7 ~ 17.4 lb-ft)

7.
Assemble the other parts in the reverse order of disassembly.
    Piston and Connecting Rod Inspection
    Connecting Rod 1. Check the side clearance between piston and connecting rod. Using filler gauge, measure the side clearance while moving the connecting rod bac ...

    Crankshaft Components
    1. Crankshaft sprocket s 2. Crankshaft thrust bearing 3. Crankshaft upper main bearing 4. Crankshaft 5. CKPS wheel 6. Crankshaft lower main bearing 7. Crankshaft ma ...

    See also:

    Repeat
    Press the key Set [ RPT] through the TUNE knob or key to repeat the current song. ❈ Press RPT again to turn off. ...

    Inhibitor Switch. Inspection
       • Thoroughly check connectors for looseness, poor connection, bending, corrosion, cont ...

    Rear Shock Absorber Inspection
    1. Check the rubber parts for wear and deterioration. 2. Compress and extend the piston rod (A) and check that there is no abnormal resista ...