Kia Soul: Front Stabilizer Bar Replacement - Front Suspension System - Suspension SystemKia Soul: Front Stabilizer Bar Replacement

Kia Soul 2014-2019 PS Service Manual / Suspension System / Front Suspension System / Front Stabilizer Bar Replacement

1.
Loosen the wheel nuts slightly.
Raise the vehicle, and make sure it is securely supported.
2.
Loosen the bolt (A) and then disconnect the universal joint assembly from the pinion of the steering gear box.
Tightening torque:
32.4 ~ 37.3N.m (3.3 ~ 3.8kgf.m, 23.9 ~ 27.5lb-ft)

  
Insert to the shaft in order that the center of the bolt and the marking (A) is in a straight line.
3.
Remove the front wheel and tire (A) from front hub.
Tightening torque:
88.2 ~ 107.8N.m (9.0 ~ 11.0kgf.m, 65.0 ~ 79.5lb-ft)

  
•
Be careful not to damage to the hub bolts when removing the front wheel and tire (A).
4.
Remove the stabilizer link (A) loosening the nut.
Tightening torque:
98.1 ~ 117.7N.m(10.0 ~ 12.0kgf.m, 72.3~86.8lb-ft)

5.
Remove the tie rod end ball joint (C) from the knuckle by using the SST (09568-34000).
(1)
Remove the split pin (A).
(2)
Remove the castle nut (B).
(3)
Use the SST (09568-34000).
Tightening torque:
23.5 ~ 33.3N.m (2.4 ~ 3.4kgf.m, 19.4 ~ 24.6lb-ft)

  
•
When using SST, be sure not to damage the dust cover of lower arm ball joint.
•
Keep SST tied to the car because there is a risk of injury by dropping the SST during removing the lower arm ball joint.
•
The peripheral parts may be damaged when removing the lower arm ball joint with a general tool such as lever, so be sure to use SST.
6.
Loosen the bolt & nut and then remove the lower arm (A).
Tightening torque:
58.9 ~ 70.6 N.m (6.0 ~ 7.2 kgf.m, 43.4 ~ 52.1 lb-ft)

7.
Loosen the bolt and then separate the roll rod stopper (A).
Tightening torque:
107.9 ~127.5N.m(11.0 ~ 13.0kgf.m, 79.6 ~ 94.0lb-ft)

8.
Disconnect the muffler rubber hanger (A).
9.
Loosen the bolts & nuts and then remove the sub frame (A).
Tightening torque
Sub frame mounting bolts & nuts :
156.9 ~ 176.5N.m(16.0 ~ 18.0kgf.m, 115.7 ~ 130.2lb-ft)

10.
Remove the heat protector (A).
Tightening torque:
6.9 ~ 10.8N.m (0.7 ~ 1.1kgf.m, 5.1 ~ 7.9lb-ft)

11.
Remove the stabilizer (A) from the front sub frame by loosening the mounting bolts & nuts.
Tightening torque:
44.1 ~ 53.9N.m(4.5 ~ 5.5kgf.m, 32.5 ~ 39.8lb-ft)

12.
Check the wheel Alignment.
(Refer to Tires/Wheels - "Alignment")
    Front Lower Arm Inspection
    1. Check the bushing for wear and deterioration. 2. Check the front stabilizer bar for deformation. 3. Check th ...

    Front Stabilizer Bar Inspection
    1. Check the bushing for wear and deterioration. 2. Check the front stabilizer bar for deformation. ...

    See also:

    Start/Stop Button Installation
    1. Install the start/stop button. 2. Install the console upper cover. 3. Connect the ...

    In case of an emergency while driving
    If the engine stalls at a crossroad or crossing If the engine stalls at a crossroad or crossing, set the shift lever in the N (Neutral) position and then push the vehicle to a safe place. If you h ...

    ETC (Electronic Throttle Control) System. Troubleshooting
    Fail-Safe Mode Item Fail-Safe ETC Motor Throttle valve stuck at 7° TPS TPS 1 fault ECM looks at TPS2 TPS 2 fault ECM ...