Kia Soul: Front Hub / Knuckle Replacement - Front Axle Assembly - Driveshaft and axleKia Soul: Front Hub / Knuckle Replacement

Kia Soul 2014-2019 PS Service Manual / Driveshaft and axle / Front Axle Assembly / Front Hub / Knuckle Replacement

1.
Loosen the wheel nuts slightly.
Raise the vehicle, and make sure it is securely supported.
2.
Remove the front wheel and tire (A) from front hub.
Tightening torque:
88.3 ~ 107.9 N.m (9.0 ~ 11.0 kgf.m, 65.1 ~ 79.6 lb-ft)

  
Be careful not to damage to the hub bolts when removing the front wheel and tire (A).
3.
Loosen the guide rod bolt (B) and pivot the caliper (A) up out of the way.
Tightening torque:
21.6 ~ 31.4 N.m (2.2 ~ 3.2 kgf.m, 15.9 ~ 23.1 lb-ft)

4.
Remove the brake pads (A).
5.
Remove the brake caliper mounting bolts (A), and then place the brake caliper assembly (B) with wire.
Tightening torque:
78.4 ~ 98.0 N.m (8.0 ~ 10.0 kgf.m, 57.8 ~ 72.3 lb-ft)

6.
Loosen the front brake disc mount screw (B) and then remove the front brake disc (A).
Tightening torque:
4.9 ~ 5.9 N.m (0.5 ~ 0.6 kgf.m, 3.6 ~ 4.3 lb-ft)

7.
Remove driveshaft nut (A) from the front hub under applying the break.
Tightening torque:
240.3 ~ 269.7 N.m (24.5 ~ 27.5 Kgf.m, 177.2 ~ 197.9 lb-ft)

  
•
The driveshaft lock nut should be replaced with new ones.
•
After installation driveshaft lock nut, stake the lock nut using a chisel and hammer as shown in the illustration below.

8.
Remove the tie rod end ball joint (C) from the knuckle by using the SST (09568-34000).
(1)
Remove the split pin (A).
(2)
Remove the castle nut (B).
(3)
Use the SST (09568-34000).
Tightening torque:
23.5 ~ 33.3N.m (2.4 ~ 3.4kgf.m, 19.4 ~ 24.6lb-ft)

  
•
When using SST, be sure not to damage the dust cover of lower arm ball joint.
•
Keep SST tied to the car because there is a risk of injury by dropping the SST during removing the lower arm ball joint.
•
The peripheral parts may be damaged when removing the lower arm ball joint with a general tool such as lever, so be sure to use SST.
9.
Loosen the mount bolt and then remove the wheel speed sensor (A) from knuckle.
Tightening torque:
6.8 ~ 10.7 N.m (0.7 ~ 1.1 kgf.m, 5.0 ~ 7.9 lb-ft)

10.
Loosen the bolt & nut and then remove the lower arm (A).
Tightening torque:
58.8 ~ 70.6 N.m (6.0 ~ 7.2 kgf.m, 43.4 ~ 52.1 lb-ft)

11.
Disconnect the driveshaft (A) from the front hub assembly.
12.
Loosen the strut mounting bolts (A) and then remove the knuckle assembly (B).
Tightening torque:
137.3 ~ 156.9 N.m (14.0 ~ 16.0 kgf.m, 101.3 ~ 115.7 lb-ft)

    Front Hub / Knuckle Components
    1. Brake disc 2. Wheel hub assembly 3. Hub bolt 4. Dust cover 5. Knuckle 6. Hub bearing 7. Snap ring ...

    Front Hub / Knuckle Disassembly
    1. Remove the snap ring (A). 2. Remove the hub assembly from the knuckle assembly. (1) Install the ...

    See also:

    Smart Key Unit Circuit Diagram
    ...

    Closing the hood
    1. Before closing the hood, check the following: • All filler caps in the engine compartment must be correctly installed. • Gloves, rags or any other combustible material must be removed from th ...

    Front Door Trim Component Location
    1. Front door trim ...