Kia Soul: Rear Seat Back Cover Replacement
[LH] |
|
|
1. |
Remove the rear seat back assembly [LH].
(Refer to Rear Seat - "Rear Seat Assembly")
|
2. |
Push the lock pin (B), remove the rear seat headrest (A).
|
3. |
Remove the lock hook (B) and then remove the rear seat armrest
(A).
|
4. |
Press the rear seat armrest (A) in the direction of the arrow
in the below picture, and then remove it by pulling it up.
|
5. |
Using a screwdriver or remover, remove the rear seat folding bezel
(A).
|
6. |
Using a screwdriver or remover, remove the rear seat belt center
cover (A).
|
7. |
Using a screwdriver or remover, remove the tether anchor ganish
(A).
|
8. |
Using a screwdriver or remover, remove the rear seat back bush
hinge (A).
|
9. |
Remove the protector (A) located in the bottom side of the rear
seat back.
|
10. |
Zip off the rear seat back cover located in the side (A), and
then pull it up.
|
11. |
Pull out the hooks (A) by the rear seat back frame.
|
12. |
Turn the rear seat back cover inside out. Then pull out the headrest
guides (A) while pinching both sides of the lower part of the guides,
and remove them.
|
13. |
Remove the rear seat back cover (A) from the rear seat back frame
(B).
|
14. |
After removing the hog-ring clips (A) on the rear of seat back
and remove the rear seat back cover (B).
|
15. |
Install in the reverse order of removal.
|
[RH] |
|
|
1. |
Remove the rear seat back assembly [RH].
(Refer to Rear Seat - "Rear Seat Assembly")
|
2. |
Push the lock pin (B), remove the rear seat headrest (A).
|
3. |
Using a screwdriver or remover, remove the rear seat folding bezel
(A).
|
4. |
Using a screwdriver or remover, remove the tether anchor ganish
(A).
|
5. |
Using a screwdriver or remover, remove the rear seat back bush
hinge (A).
|
6. |
Remove the protector (A) located in the bottom side of the rear
seat back.
|
7. |
Zip off the rear seat back cover located in the side (A), and
then pull it up.
|
8. |
Pull out the hook (A) by the rear seat back frame.
|
9. |
Turn the rear seat back cover inside out. Then pull out the headrest
guides (A) while pinching both sides of the lower part of the guides,
and remove them.
|
10. |
Remove the rear seat back cover (A) from the rear seat back frame
(B).
|
11. |
After removing the hog-ring clips (A) on the rear of seat back
and remove the rear seat back cover (B).
|
12. |
Install in the reverse order of removal.
|
Rear Seat Back Cover Component Location
1. Rear seat back cover [LH]
2. Rear seat back cover [RH]
...
Rear Seat Cushion Cover Component Location
1. Rear seat cushion cover
...
See also:
Climate control air filter (if equipped)
The climate control air filter installed behind the glove box filters the dust
or other pollutants that come into the vehicle from the outside through the heating
and air conditioning system. ...
Vacuum crankcase ventilation hoses (if equipped)
Inspect the surface of hoses for evidence of heat and/or mechanical damage. Hard
and brittle rubber, cracking, tears, cuts, abrasions, and excessive swelling indicate
deterioration.
Particular at ...
Warning lights
✽ NOTICE - Warning lights
Make sure that all warning lights are OFF after starting the engine. If any
light is still ON, this indicates a situation that needs attention.
Air bag Warning Lig ...