Kia Soul: Steering Gear box Repair procedures - Electric Power Steering - Steering SystemKia Soul: Steering Gear box Repair procedures

Kia Soul EV (PS EV) 2015-2020 Service Manual / Steering System / Electric Power Steering / Steering Gear box Repair procedures

Replacement
1.
Loosen the wheel nuts slightly.
Raise the vehicle, and make sure it is securely supported.
2.
Loosen the bolt and then disconnect the universal joint assembly (A) from the pinion of the steering gear box.

Tightening torque :
32.4 ~ 37.3N.m (3.3 ~ 3.8kgf.m, 23.9 ~ 27.5lb-ft)

   
Insert to the shaft in order that the center of the bolt and the marking (A) is in a straight line.
3.
Remove the front wheel and tire (A) from front hub.

Tightening torque :
88.2 ~ 107.8N.m (9.0 ~ 11.0kgf.m, 65.0 ~ 79.5lb-ft)

   
Be careful not to damage to the hub bolts when removing the front wheel and tire (A).
4.
Remove the stabilizer link (A) loosening the nut.

Tightening torque :
98.1 ~ 117.7N.m(10.0 ~ 12.0kgf.m, 72.3~86.8lb-ft)

5.
Remove the tie rod end ball joint (C) from the knuckle by using the SST (09568-34000).
(1)
Remove the split pin (A).
(2)
Remove the castle nut (B).
(3)
Use the SST (09568-34000).

Tightening torque :
23.5 ~ 33.3N.m(2.4 ~ 3.4kgf.m, 17.4 ~ 24.6lb-ft)

   
When using SST, be sure not to damage the dust cover of lower arm ball joint.
Keep SST tied to the car because there is a risk of injury by dropping the SST during removing the lower arm ball joint.
The peripheral parts may be damaged when removing the lower arm ball joint with a general tool such as lever, so be sure to use SST.
6.
Loosen the bolt & nut and then remove the lower arm (A).

Tightening torque :
58.9 ~ 70.6 N.m (6.0 ~ 7.2 kgf.m, 43.4 ~ 52.1 lb-ft)

7.
Loosen the bolt and then separate the roll rod stopper (A).

Tightening torque :
107.9 ~127.5N.m(11.0 ~ 13.0kgf.m, 79.6 ~ 94.0lb-ft)

8.
Loosen the bolts & nuts and then remove the sub frame (A).

Tightening torque :
Sub frame mounting bolt & nut
156.9 ~ 176.5N.m(16.0 ~ 18.0kgf.m, 115.7 ~ 130.2lb-ft)

9.
Remove the stabilizer (A) from the front sub frame by loosening the mounting bolts & nuts.

Tightening torque :
44.1 ~ 53.9N.m(4.5 ~ 5.5kgf.m, 32.5 ~ 39.8lb-ft)

10.
Remove the gear box (A) from the front sub frame by loosening the mounting bolts.

Tightening torque :
88.3 ~ 107.9N.m (9.0 ~ 11.0kgf.m, 43.4 ~ 57.9lb-ft)

11.
Installation is the reverse of removal.
   
Must be ASP calibration and EPS type recognition after assembling.
12.
Check the wheel Alignment.
(Refer to Suspension System - "Alignment")
    Steering Gear box Components and Components Location
    Components 1. Steering Gear box ...

    See also:

    Jump starting
    Jump starting can be dangerous if done incorrectly. Therefore, to avoid harm to yourself or damage to your vehicle or battery, follow these jump starting procedures. If in doubt, we strongly recom ...

    Shopping bag holder
    Do not hang a bag weighing more than 7 lbs. (3 kg). It may cause damage to the shopping bag holder. ...

    Alternator Specification
    Alternator ltem Specification Nominal output 13.5V, 110A Speed in use 1,000 ~ 18,000 rpm Voltage regulator IC Regulator bu ...