Kia Soul: Rear Disc Brake. Removal - Brake System - Brake SystemKia Soul: Rear Disc Brake. Removal

Kia Soul 2014-2019 PS Service Manual / Brake System / Brake System / Rear Disc Brake. Removal

Brake caliper assembly
1.
Remove the front wheel & tire.

Tightening torque :
88.3 ~ 107.9 N.m (9.0 ~ 11.0 kgf.m, 65.1 ~ 79.6 lb-ft)

2.
Remove the hose eyebolt (A).

Tightening torque :
24.5 ~ 29.4 N.m (2.5 ~ 3.0 kgf.m, 18.1 ~ 21.7 lb-ft)

3.
Remove the parking brake cable (A), after removing the clip (B).

  
Parking brake lever in the car must be in fully loosened position.
4.
Loosen the guide rod bolt (B) and the remove the rear caliper body (A).

Tightening torque :
21.6 ~ 31.4 N.m (2.2 ~ 3.2 kgf.m, 15.9 ~ 23.1 lb-ft)

5.
Remove the brake pads (B) and pad retainers (C) in the caliper carrier (A).

6.
Loosen the caliper mounting bolts (B) and then remove the caliper carrier (A).

Tightening torque :
63.7 ~ 73.5 N.m (6.5 ~ 7.5 kgf.m, 47.0 ~ 54.2 lb-ft)

Rear Wheel Brake disc
1.
Remove the front wheel & tire.

Tightening torque :
88.3 ~ 107.9 N.m (9.0 ~ 11.0 kgf.m, 65.1 ~ 79.6 lb-ft)

2.
Loosen the guide rod bolt (B) and the remove the rear caliper body (A).

Tightening torque :
21.6 ~ 31.4 N.m (2.2 ~ 3.2 kgf.m, 15.9 ~ 23.1 lb-ft)

3.
Remove the brake pads (B) and pad retainers (C) in the caliper carrier (A).

4.
Loosen the caliper mounting bolts (B) and then remove the caliper carrier (A).

Tightening torque :
63.7 ~ 73.5 N.m (6.5 ~ 7.5 kgf.m, 47.0 ~ 54.2 lb-ft)

5.
Remove the rear brake disc by loosening the screws (A).

Tightening torque :
4.9 ~ 5.9 N.m (0.5 ~ 0.6 kgf.m, 3.6 ~ 4.3 lb-ft)

    Rear Disc Brake. Components
    1. Guide rod bolt 2. Bleed screw 3. Caliper carrier 4. Caliper body 5. Brake pad 6. Pad retainer ...

    Rear Disc Brake. Replacement
    Rear brake pads 1. Remove the front wheel & tire. 2. Loosen the guide rod bolt (B) and the remove the rear caliper body (A). ...

    See also:

    Rear Door Belt Inside Weatherstrip Repair procedures
    Replacement 1. Remove the rear door trim. (Refer to Rear Door - "Rear Door Trim") 2. Remove the rear door belt inside weatherstrip (A). 3. Install in the reverse order of removal. ...

    Removal
       • Put on gloves to protect your hands. & ...

    Blower Resistor (Manual) Inspection
    1. Measure the resistance between the terminals. 2. The measured resistance is not within specification, the blower resistor must be replac ...