Kia Soul: Power Window Switch Repair procedures - Power Windows - Body Electrical SystemKia Soul: Power Window Switch Repair procedures

Kia Soul EV (PS EV) 2015-2020 Service Manual / Body Electrical System / Power Windows / Power Window Switch Repair procedures

Inspection
Power Window Main Switch Inspection
1.
Disconnect the negative (-) battery terminal.
2.
Remove the front door trim.
(Refer to Body - "Front Door Trim")
3.
Disconnect the connector (A) from the power window switch module.

4.
Check for continuity between the terminals in each switch position according to the table.
[Driver/Assist Safety]

[Driver Auto Down]

Assist Power Window Switch Inspection
1.
Disconnect the negative (-) battery terminal.
2.
Remove the front door trim panel.
(Refer to Body - "Front Door Trim")
3.
Disconnect the connector (A) from the switch.

4.
Check for continuity between the terminals in each switch position according to the table. If the continuity condition is not normal, replace the switch.
[Safety]

[Manual]

Rear Power Window Switch Inspection
1.
Disconnect the negative (-) battery terminal.
2.
Remove the rear door trim panel.
(Refer to Body - "Rear Door Trim")
3.
Disconnect the connector (A) from the switch.

4.
Check for continuity between the terminals in each switch position according to the table. If the continuity condition is not normal, replace the switch.
[With Seat Heater]

[Without Seat Heater]

Removal
Driver Power Window Switch
1.
Disconnect the negative (-) battery terminal.
2.
Remove the front door trim.
(Refer to Body - "Front Door Trim")
3.
Remove the power window switch assembly (A) by loosening the mounting screws (8EA).

4.
Remove the power window switch assembly (A) after loosening the mounting screws.

Assist Power Window Switch
1.
Disconnect the negative (-) battery terminal.
2.
Remove the front door trim.
(Refer to Body - "Front Door Trim")
3.
Remove the power window switch assembly (A) by loosening the mounting screws (7EA).

4.
Remove the power window switch assembly (A) after loosening the mounting screws.

Rear Power Window Swtich
1.
Disconnect the negative (-) battery terminal.
2.
Remove the rear door trim.
(Refer to Body - "Rear Door Trim")
3.
Remove the power window switch assembly (A) by loosening the mounting screws (7EA).

4.
Remove the power window switch assembly (A) after loosening the mounting screws.

Installation
Driver Power Window Switch
1.
Install the power window switch assembly.
2.
Install the front door trim after connecting the connector.
Assist Power Window Switch
1.
Install the power window switch assembly.
2.
Install the front door trim after connecting the connector.
Rear Power Window Swtich
1.
Install the power window switch assembly.
2.
Install the front door trim after connecting the connector.
    Power Window Switch Schematic Diagrams
    Circuit Diagram Driver Power Window Switch Assist Power Window Switch Rear Power Window Switch ...

    Power Window Relay Repair procedures
    Inspection Diagnosis With GDS 1. It can quickly diagnose defects of power window by communicating with GDS. GDS can operate actuator forcefully, monitor input/output values and self diagnose. ...

    See also:

    High beam indicator light, High beam assist indicator
    High beam indicator light This indicator light illuminates: When the headlights are on and in the high beam position When the turn signal lever is pulled into the Flash-to-Pass position. H ...

    Air bag - advanced supplemental restraint system
    * The actual air bags in the vehicle may differ from the illustration. (1) Driver’s front air bag (2) Passenger’s front air bag (3) Side impact air bag (4) Curtain air bag Even in vehicles ...

    Hood Lift Repair procedures
    Replacement     • When removing and installing the hood lifter, work in a group of two or more. • When removing the clips, use a clip remover. 1. ...