Kia Soul: Head Lamps Replacement - Lighting System - Body Electrical System - Kia Soul 2014-2019 PS Service ManualKia Soul: Head Lamps Replacement

Second generation PS (2014-2019) / Kia Soul 2014-2019 PS Service Manual / Body Electrical System / Lighting System / Head Lamps Replacement

Head Lamp Low Beam (HID)
1.
Turn the head lamp switch off.
2.
Disconnect the power connector from the lamp.
3.
Remove the dust cap (A).
4.
Remove the ignitor clip (A) from the lamp assembly after loosening the mounting screws.
5.
Remove the ignitor and bulb (A).
6.
Disconnect the ignitor connector (A).
7.
Installation is the reverse of removal.
  
Turn the head lamp switch off to avoid high voltage
Be careful not to damage the bulb and use genuine bulbs only
•
Do not apply excessive force and fit it correctly.
•
Confirm the bulb locking
Head Lamp Low Beam (Bulb)
1.
Turn the head lamp switch off.
2.
Disconnect the power connector from the lamp.
3.
Remove the dust cap (A).

4.
Remove the sockect (A) from the head lamp assembly.
5.
Remove the bulb (A) from the connector.
6.
Installation is the reverse of removal.
Head Lamp High Beam (Bulb)
1.
Turn the head lamp switch off.
2.
Disconnect the power connector from the lamp.
3.
Remove the dust cap (A).
4.
Disconnect the connector (A) from the bulb.
5.
Separate the fixed clip (A).
6.
Remove the head lamp high beam bulb (A).
7.
Installation is the reverse of removal.
Turn signal lamp
1.
Turn the head lamp switch off.
2.
Remove the bulb socket (A) and bulb (B) from the lamp assembly.
Ballast
1.
Turn the head lamp switch off.
2.
Disconnect the power connector from the lamp.
3.
Remove the head lamp assembly.
4.
Remove the ballast (A) after loosening the screws.
5.
Disconnect the connectors (A) from the ballast.
6.
Installation is the reverse of removal.
  
•
Turn the head lamp switch off to avoid high voltage.
  
•
HID lamp shall not be used on other cars.(Fire may occur.)
•
Fire may occur when HID lamp initially lights due to the fact that arc-discharge generates high voltage (max. 20,000V) and high current (12-13A), and are different from the halogen lamp specification.
•
Install the dust cover after confirming the locking state between bulb and bulb holder.
•
When testing the HID head lamp, turn the power on or off with switch between power supply and lamp because of high voltage.
•
Do not operate the head lamp switch with the bulb not installed, because it generates spark momently.
    Head Lamps Installation
    1. Install the head lamp bulbs. 2. Reassemble the head lamp bulb covers. 3. Reassembl ...

    Head Lamp Aiming Instructions
    The head lamps should be aimed with the proper beam-setting equipment, and in accordance with the equipment manufacturer's instructions.    ...

    See also:

    Changing Song/File
    While song (file) is playing key Shortly pressing the key : Plays the current song from the beginning. ❈ If the key is pressed again within 2 second, the previous song is played. Pres ...

    Turn signal indicator
    The blinking green arrows on the instrument panel show the direction indicated by the turn signals. If the arrow comes on but does not blink, blinks more rapidly than normal, or does not illumin ...

    Torque Converter Control Solenoid Valve (T/CON_VFS). Specifications
    Direct control VFS[T/CON] ▷ Control type : Normal low type Control Pressure kpa (kgf/cm², psi) 9.81 ~ 500.14 (0.1 ~ 5.1, 1.42 ~ 72.54) Current value(mA) ...