Put on gloves to protect your hands.
•
When prying with a flat-tip screwdriver, wrap it with
protective tape, and apply protective tape around the related parts, to
prevent damage.
•
Use a plastic panel removal tool to remove interior trim pieces to protect from marring the surface.
•
Take care not to bend or scratch the trim and panels.
1.
Disconnect the negative (-) battery terminal.
2.
Remove the center fascia panel (A) from the crash pad.
3.
Disconnect the connecters (A) from the center fascia panel.
4.
Remove the audio head unit (A) after loosening the mounting screws.
5.
Disconnect the connectors and cable (A) from the audio head unit.
1.
Connect the connectors and cable.
2.
Install the audio head unit and center fascia panel.
3.
Connect the negative (-) battery terminal.
1)
Make sure the connector are connected inproperly.
2)
Check the audio system.
1.
Check the specified value of AVN head unit connectors in specified condition.
Connector A
No. Name Terminal Description Condition Specified Condition A1 Rear left speaker (+) Loudspeaker Rear Left+ Needed connection to the car Analog output A2 Front left speaker (+) Loudspeaker Front Left+ Needed connection to the car Analog output A3 Front right speaker (+) Loudspeaker Front Right+ Needed connection to the car Analog output A4 Rear right speaker (+) Loudspeaker Rear Right+ Needed connection to the car Analog output A5 - - ? ? A6 - - ? ? A7 - - ? ? A8 Illumination (+) Rheostat from vehicle + Needed connection to the car ? A9 Detent Detent Needed connection to the car ? A10 Rear left speaker (-) Loudspeaker Rear Left- Needed connection to the car Analog output A11 Front left speaker (-) Loudspeaker Front Left- Needed connection to the car Analog output A12 Front right speaker (-) Loudspeaker Front Right- Needed connection to the car Analog output A13 Rear right speaker (-) Loudspeaker Rear Right- Needed connection to the car Analog output A14 - - ? ? A15 - - ? ? A16 - - ? ? A17 Illumination (-) Rheostat from vehicle - Needed connection to the car ? A18 Remote antenna Remote Power supply for Antenna Acc on 9V ~ 18V
Connector B
No. Name Terminal Description Condition Specified Condition B1 - - ? ? B2 - - ? ? B3 - - ? ? B4 Steering remocon Steering Wheel Remote Control Steering Wheel switch pushed 0.5V ~ 3V B5 - - ? ? B6 USB D (+) USB D+ USB device is inserted 3.2V ~ 3.45 B7 USB/ iPod VDD USB /iPod power USB/iPod device is inserted 4.9V ~ 5.1V B8 AUX R input AUX Right Sound Signal External Auxiliary device is Audio playing (At time of Aux jack use) A waveform synchronized with sound is output B9 AUX ground AUX Reference Ground Always Below 1 ohm B10 Mic (+) (Bluetooth) Bluetooth MIC+ Input the Voice Signal via MIC A waveform synchronized with Voice data via MIC B11 ACC Accessory Engine switch on(ACC) 11 ~ 14 V B12 Battery (+) Battery Always 11 ~ 14 V B13 - - ? ? B14 - - ? ? B15 - - ? ? B16 Vehicle speed Speed Sensor Signal Engine switch on(IGN), car is moved slowly Approx. 5V Level Pulse Generation B17 Remote control ground Steering Wheel Remote Control Gnd Always Below 1 ohm B18 USB D (-) USB D- USB device is inserted 3.2V ~ 3.45 B19 USB/ iPod ground iPod detection line iPod device is inserted GND B20 AUX detect AUX Signal Input Detect Auxiliary device is inserted 0V(Low) > 5V(High) B21 AUX L input AUX Left Sound Signal External Auxiliary device is Audio playing (At time of Aux jack use) A waveform synchronized with sound is output B22 Mic (-) (Bluetooth) Bluetooth MIC- Input the Voice Signal via MIC A waveform synchronized with Voice data via MIC B23 - - ? ? B24 Power ground Ground Always Below 1 ohm
Components
Connector Pin Information
No.Connector AConnector B1Rear left speaker (+)-2Front left speaker (+)-3Front right speaker (+)-4Rear right speaker (+)Steering remocon5--6-USB D (+)7-USB/ ...
Inspection
1.
Troubleshooting for Speaker
(1)
Basic inspection of speaker
Inspect the sound from speaker after verifying that the
speaker mounting screws is removed and the wiring connector i ...
See also: Inspection
Front Door Lock Module Inspection
1.
Remove the front door trim.
(Refer to Body - "Front Door Trim")
2.
...
Time Format
This function is used to set the 12/24 hour time format of the audio system.
Select [Time Format] Set 12Hr / 24Hr through
TUNE knob
Clock Display when Power is OFF
Select [Clock Disp.(Pwr Off) ...
Chiller Components and Components Location
Components Location
1. Chiller
...